A Step-by-Step Overview to Installing a Bath Tub
A Step-by-Step Overview to Installing a Bath Tub
Blog Article
What're your opinions with regards to A Step-by-Step Guide to Installing a Bathtub?
Mounting a tub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily available, the task can move rapidly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and set in the brand-new one. See to it you have actually certified yourself for the task and also are comfortable attempting it. As opposed to hiring a professional to take control of a halfway-completed project, it is much better to take into consideration using one before you start. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly aid you install a new bath tub in your washroom if you have already gotten a brand-new tub and do not require to transform the arrangement of your previous water system pipelines.
Your devices and material list need to consist of the following:
Planning for the Installment
To start with, the supporting frame supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to now be ready to be suited its final position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be rather problematic as a result of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, put the bath tub in the needed placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the outermost flexible tap adapter to the suitable supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the water supply as well as examine all joints and new pipework for leakages and tighten them if required. Load the bathtub and additionally examine the overflow outlet as well as the regular outlet for leaks.
Lastly, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has actually been made use of at least once as this will certainly resolve it right into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will require decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in location in between the faucet as well as the sink. Safeguard the faucet in position with the supplier given backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former kind should be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a stiff seal, triggering the water to penetrate the wall surface in between the bath and the tiling, bring about issues with dampness and feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in use. The sealer can split fairly very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads on Tools You Need to Install a New Bathtub , I thought sharing that article post was a smart idea. Liked our piece? Please share it. Help another person check it out. Thank you so much for going through it.
Get Quote Now
Report this page